Ensoft - S® - SEBS

Is our brand name for compounds based on saturated styrenic block copolymer SEBS (styrene-ethylene-butylene-styrene) and polyolef ins mainly Polypropylene (PP). The compounds have excellent rubberlike elasticity and weathering resistance. Ensoft-S® Range can easily be self-colored with the use of proper Masterbatch or provided as pre-colored compounds. Typical properties of Ensoft-S® Series are given below.

General Properties:

* Hardness range from 5 Shore A to 60 Shore D

* Service Temperature: -50° C - +110° C (dynamic) -50- + 120° C (Static/Peak)

* Excellent ozone, UV and weather resistance due to saturated elastomeric phase

* Chemical resistance against many aggressive media

* Low compression set and good elasticity in a wide temperature range

* Ease of processing (no pre-drying is required) and recyclability

Special Ensoft-S® Series Have Following Properties:

* FDA Compatible

* Adhesion to a broad range of polar and non-polar substrates

Such as PP, PA, ABS, PC, PS.

* High temperature resistance

* Low fogging

* High transparency

* Low compression set at high temperatures

* Expandable

* Excellent abrasion resistance

* Flammability (UL 94 V0)

* CSTB, RAL GZ-716 /1 approvals

Possible Applications:

Automotive; Bellows, boots and grommets, air ducts and overmolded duct seals, lens gaskets, fender guards, sun visors, soft touch interior components, glass encapsulations

Appliance / Houseware: Overmolded grips for power tools, dishwasher & refrigerator seals, gaskets, anti-vibration parts, drainage/discharge hoses and fittings

Electricity & Electronic: Molded-in seals for electrical components, wire and cable insulation and termination boots, connectors and housings

Health & Care: Toothbrushe handles, shaver handles, handles for other personal care utensils

Enflex - V® - TPV

Enflex-V® Is our brand name for dynamically vulcanized ethylene/propylene/diene (EPDM) and Polypropylene (PP) blends. Fully cured EPDM particles that are homogenously distributed in the thermoplastic polypropylene phase give these compounds unique rubber-like properties, with the advantage of thermoplastic processing techniques. Enflex-V® Range can be self-colored with the use of proper MB or provided as pre-colored compounds. Typical properties of Enflex-V® Series are given below.

General Properties:

* Hardness range from 45 Shore A to 60 Shore D

* Service Temperature: -50° C - +125° C (dynamic) -50- + 135° C (Static/Peak)

* Excellent ozone, UV and weather resistance due to saturated elastomeric phase

* Chemical resistance to aggressive mediums

* Very Low (Rubberlike) compression set and good elasticity (that does not change

Significantly over time) in a wide temperature range.

Special Enflex-V® Series have following properties:

* Adhesion to a broad range of polar and non-polar substrates such as PP, PA, ABS, PC

* Broad product range including Halogen Free FR, improved oil resistance, improved temperature resistance, high flow and other specialty grades.

* Recyclability and lower processing costs with respect to traditional cured rubbers

* Lower density

* Very good resistance to "fatigue" and tear strength

* Low fogging

* Flammability (UL 94 V0)

* CSTB, RAL GZ-716/1 approvals

Possible Applications

Automotive - Interior: Interior console parts, Anti-slip pads, Gearbox cover, Gear handle, Car mats,

Seals for air ducts, Seatbelt covers, Car seat adjusting lever, Airbag covers

Automotive - Exterior: Body gasket and seals, Seals/Gaskets for signal indicators, headlamps, mirrors, Mud flap, Window seals and encapsulation, Spoilers and edge trims

Automotive - Under the hood: Bellows and gommets, Seals for electric housings, Air ducts and duct seals