Basic Info.
Model NO.
DCE156QUM-N10-W600
Usage
Monitor LCM, Notebook LCM
Digital LCD Module Type
TFT-LCD Module
Touch Screen Type
Capacitive
DOT-Matrix Graphic LCD Module Type
RGB Vertical Stripe Arrangement
LCD Drive Mode
Multiplex Drive LCD Module
Active Area
345.6 (H) × 194.4 (V) mm
Number of Pixels
3840(H) × 2160(V)
Pixel Pitch
0.09(H) × 0.09 (V) mm
Pixel Arrangement
RGB Vertical Stripe
Dimensional Outline
352.4 (H) × 206.9(V) × 2.7(D) mm
Typical Luminance
600 CD/M2
Transport Package
Carton Box
Specification
Industrial-grade LCD display module
Product Description
1.0 GENERAL DESCRIPTION1.0.1 Introduction
DCE116FHB-N85-600 is a color active matrix TFT LCD FOB using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This FOB has a 11.60 inch diagonally measured active area with FHD resolutions (1920 horizontal by 1080 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7M colors.1.0.2 Features2 lane eDP Interface with 2.7Gbps Link Rates
6-bit (Hi-FRC) color depth, display 16. 7M colors
DE (Data Enable) only
Reverse Type
RoHS Compliant
1.0.3 Application
HMI (Human Machine Interface)
1.0.4 General Specification| Parameter | Specification | Unit | Remarks |
|---|
| Active area | 345.6 (H) × 194.4 (V) | mm | |
| Number of pixels | 3840(H) × 2160(V) | Pixels | |
| Pixel pitch | 0.09(H) × 0.09 (V) | mm | |
| Pixel arrangement | RGB Vertical stripe | | |
| Display colors | 16.7M | Colors | 6bit+FRC |
| Display mode | ADS | | |
| Dimensional outline | 352.4 (H) × 206.9(V) × 2.7(D) | mm | |
| Typical luminance | 600 | Cd/m2 | |
| Surface treatment | AG | | |
2.0 ABSOLUTE MAXIMUM RATINGSThe followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2.
| Parameter | Symbol | Min. | Max. | Unit | Remarks |
| Power Supply Input Voltage | VCC | 0.3 | 6 | V | |
| Operating Temperature | T_OP | 0 | 50 | °C | Environment Temperature |
| Storage Temperature | T_ST | -10 | 60 | °C | Environment Temperature |
Note: 1.When the ambient temperature is T ºC, the surface temperature of Panel can not exceed (T+15)ºC.,,3.0 ELECTRICAL SPECIFICATIONS3.0.1 TFT LCD Module
< Table 3. LCD Module Electrical Specifications >| Parameter | Symbol | Min. | Typ. | Max. | Unit | Notes |
| Power Supply Input Voltage | V_DD | 3.0 | 3.3 | 3.6 | V | - |
| Power Supply Current | I_DD | - | TBD | TBD | mA | Note 1 |
| Power Supply Inrush Current | Inrush | - | - | 3 | A | - |
| Positive-going Input Threshold Voltage | V_IT+ | - | - | +300 | mV | Vcom = 0.55V typ. |
| Negative-going Input Threshold Voltage | V_IT- | -300 | - | - | mV | Vcom = 0.55V typ. |
| Differential Input Common Mode Voltage | V_com | 0.45 | 0.55 | 0.65 | V | V_IH=100mV, V_IL=-100mV |
3.2 Back-light Unit< Table 4. LED Driving guideline specifications >| Parameter | Symbol | Min. | Typ. | Max. | Unit | Remarks |
|---|
| Power supply voltage for Backlight | V_LED | - | 30 | - | V | - |
| Power supply Current for Backlight | I_LED | - | 150 | - | mA | - |
| Power supply for Backlight | P_LED | - | 4.5 | - | W | Note 1 |
| LED Life-Time | N/A | - | 30000 | - | Hour | IF = 20mA Note 2 |
| EN Control Level (Backlight on) | V_ENH | 1.2 | - | - | V | EN logic high voltage |
| EN Control Level (Backlight off) | V_ENL | - | - | 0.6 | V | EN logic low voltage |
| PWM Control Level (High) | V_PML | 1.2 | - | - | V | - |
| PWM Control Level (Low) | V_PML | - | - | 0.6 | V | - |
| PWM Control Frequency | F_PWM | 0.1 | - | 1600 | KHz | - |
| Duty Ratio | - | - | 5 | 100 | % | - |
Notes : 1. Calculator Value for reference ILED × VLED = PLED
4.0 OPTICAL SPECIFICATIONThe test of view angle range shall be measured in a dark room (ambient luminance Less than or equal to 1lux and
temperature = 25 Positive and negative 2ºC) with the equipment of Luminance meter system (Goniometer system
and TOPCON CS2000/CA310) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0 degree. We refer to θØ=0 (=θ3 ) as the 3 o'clock direction (the "right"), θ Ø=90 (= θ12 ) as the 12 o'clock direction ("upward"), θ Ø=180 (= θ9 ) as the 9 o'clock direction ("left") and θ Ø=270(= θ6 ) as the 6 o'clock direction ("bottom").
While scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The luminance, color and uniformity (etc) should be tested by CS2000/CA310. The backlight should be operating for 10 minutes prior to measurement. VDD shall be 3.3 ± 0.3V at 25 Celsius. Optimum viewing angle direction is 6 'clock
<Table 5. Optical Specifications>| Parameter | Sub-parameter | Symbol | Condition | Min. | Typ. | Max. | Unit | Remark |
|---|
| Viewing Angle (Horizontal) | - | Θ3 | CR > 10 | - | 85 | - | Deg. | Note 1 |
| Viewing Angle (Horizontal) | - | Θ9 | CR > 10 | - | 85 | - | Deg. | Note 1 |
| Viewing Angle (Vertical) | - | Θ12 | CR > 10 | - | 85 | - | Deg. | Note 1 |
| Viewing Angle (Vertical) | - | Θ6 | CR > 10 | - | 85 | - | Deg. | Note 1 |
| Contrast ratio | - | CR | Θ = 0° | 800 | 1000 | - | - | Note 2 |
| Color Gamut | NTSC (CIE1931) | - | Θ = 0° | 92 | 98 | - | % | Note 5 |
| White Luminance uniformity | 9 Points or 5 Points | ΔY9 or ΔY5 | Θ = 0° | 70 | 72 | - | % | Note 4 |
| Color temperature | - | CT | - | - | 7000 | - | K | - |
| Reproduction of color | White (Wx) | Wx | Θ = 0° | Typ.-0.03 | 0.304 | Typ.+0.03 | - | @C Note 5 |
| Reproduction of color | White (Wy) | Wy | Θ = 0° | - | 0.316 | - | - | @C Note 5 |
| Response Time | - | Tr+Td | Ta= 25°C, Θ = 0° | - | 35 | 40 | ms | Note 6 |
| Trans. | Center | Center | Θ = 0° | 4.3% | 5.1% | - | - | @Biprism BLU |
Notes : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing angles are determined for the horizontal or 3, 9 o'clock direction and the vertical or 6, 12 o'clock direction with respect to the optical axis which is normal to the LCD surface (see FIGURE 1). CR=Luminance when displaying a white rasterLuminance when displaying a black raster2.Contrast measurements shall be made at viewing angle of Θ= 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state . (see FIGURE 1) ,Luminance Contrast Ratio (CR) is defined mathematically. 3.The color chromaticity coordinates specified in Table 5. shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel.
4. The electro-optical response time measurements shall be made as FIGURE 3 by switching the "data" input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Td.
Address:
Room 1701c1, Block a, Fencheng Zhigu Building, No. 60 Tiezai Road, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China
Business Type:
Manufacturer/Factory
Business Range:
Consumer Electronics, Electrical & Electronics
Management System Certification:
ISO 9001, ISO 14001, IATF16949
Company Introduction:
Shenzhen David Camp Electronics Co., Ltd founded in Shenzhen, a global hub for hardware innovation, we have beendeeply involved in the industrial display field for many years and are a corestrategic partner of BOE (Beijing Oriental Electronics Co., Ltd. ) for LCD screens.
Our core business is the R&D and manufacturing of LCD screen assemblymodules. We focus on industrial-grade display solutions, providinghigh-precision, high-reliability, and scenario-adaptive display technologies forindustrial control, medical, smart terminals, and 3D interaction in portabledevices.
We utilize Chengyi 802A fully automatic bonding line, Eurolink semi-automaticbonding line, COG fully automatic bonding, FOG fully automatic bonding, FOGfully automatic dispensing machine, FOB drying machine, and FOBsemi-automatic pressing machine.
